2008-06-08

MG# 103 Zaku MS-06R: 雙脚の製作 - 2

繼續小腿的噴射器上半部:


小腿的龍骨差不多完成:




補品 - 金屬噴射器:


覺得齋銀色好單調, 加小小detail:


上次製作小腿的噴射器上半部時鑽了小孔, 是為了裝金屬噴射器時可以穩D! 而金屬噴射器中的小孔直徑是1.5mm, 但我又揾唔到1.5mm的圓支! 只好買2mm自己磨幼!
左邊是2mm, 右邊已磨幼到1.5mm (can't see the difference?):


然後切小段裝上噴射器的上半部:


最後用krazy glue把金屬噴射器定位:



補品 - 金屬動力管:


因補品的彈弓比原裝的幼, 金屬管套唔到原裝的彈弓!
(左邊是原裝)


又要磨餐死!


OK!


再把補品的彈弓噴深鐵色:


攪掂:


裝上之後:




中途整埋下體:




唔差在條小蠻腰:





宵夜時間:


今次係在台北買的核桃鳳梨酥:


有細細粒的核桃, 比一般的鳳梨酥香口!


可以去咦道買:



Part 3: 雙脚の製作 - 1
Part 2: Day 2
Part 1: New Project


つづく

at
Labels:

25 comments:

  1. 月月Sunday, June 8, 2008 at 5:33:00 PM GMT+8

    you have completed more....wow, going oversea trips...and still have time for the zaku...OMG
    [版主回覆06/08/2008 13:13:00]只係多咗條小蠻腰姐...

    ReplyDelete
  2. AnthonySunday, June 8, 2008 at 6:45:00 PM GMT+8

    You are so pro now, can't wait to see the final product!
    [版主回覆06/08/2008 13:14:00]Not really pro at all but Mabel says I'm very 有心機...

    ReplyDelete
  3. BlooderLeeSunday, June 8, 2008 at 8:30:00 PM GMT+8

    一口气看完MG103#进度，J兄对内构细节的刻画真是仔细啊，期待完成作品。J兄端午快乐哦
    [版主回覆06/08/2008 13:16:00]Blooder兄端午快乐... 亞嫂有無包糭给你呢?

    ReplyDelete
  4. ChewSunday, June 8, 2008 at 9:48:00 PM GMT+8

    J兄，端午节快乐！好仔细的改造，加油！请教一下！我用灌装漆上色后，喷消光漆(用灌装)颜色就变了其他色，有什么办法让他不走色? 是不是消光后才上色?谢谢 ！
    [版主回覆06/08/2008 16:34:00]端午節快樂! 吃糉未? 消光係令光線反射減低, 所以你會覺得顏色有變。 但這都是正常的影響, 千萬不要先噴消光後上主色, 無用的... 如果消光後覺得顏色變得深暗, 主色就可能要鮮一点... 試多幾次你就會明白...

    ReplyDelete
  5. ChewMonday, June 9, 2008 at 2:03:00 AM GMT+8

    J兄意思是话上色就要深点，对吗?
    [版主回覆06/08/2008 23:17:00]不是要深点, 是要鮮点... 諗諗下你是否噴消光後有些變白的問題? 如果是, 應該係天氣濕的關係! 可以試試水性的消光油 - 郡氏藍色小罐, 輕輕的噴兩次, 記得噴第一次之後要等佢乾透才可噴第二次! 試試吧...

    ReplyDelete
  6. NeoMonday, June 9, 2008 at 3:13:00 AM GMT+8

    次次黎偷師都肚仔餓~!
    吃糭節快樂!
    [版主回覆06/08/2008 23:18:00]阿樂仔食糭節快樂! 不過唔好食太多呀

    ReplyDelete
  7. TerenceMonday, June 9, 2008 at 3:16:00 AM GMT+8

    Happy端午節呀``` 有新進度囉喔````
    整得咁靚```搞到人地想你快D搞掂佢睇成品添```
    點解放鳳梨酥上嚟嘅```唔係應該應下節放只糉嘅咩？
    咁細塊```唔夠你食過喔```
    [版主回覆06/08/2008 23:22:00]端午節快樂! 我唔敢食太多啦! 在香港時係要瘦瘦身, 這幾晚只吃了兩晚宵夜!

    ReplyDelete
  8. 地理堂Monday, June 9, 2008 at 3:55:00 AM GMT+8

    油得好仔細喎
    [版主回覆06/08/2008 23:25:00]因為今次係用來送俾朋友作結婚禮物, 所以先會把所有的零件仔細油一趟...

    ReplyDelete
  9. 政豪Monday, June 9, 2008 at 4:18:00 AM GMT+8

    good!!!
    [版主回覆06/08/2008 23:25:00]Thanks!!!

    ReplyDelete
  10. 沛文Monday, June 9, 2008 at 5:19:00 AM GMT+8

    上色上得好鬼靚....係用咩上
    會唔會整埋遲D出GA [RX-78]?
    [版主回覆06/08/2008 23:26:00]双星罐噴加手油... 隻RX-78 Ver2.0當然會啦...

    ReplyDelete
  11. Chaves DingMonday, June 9, 2008 at 7:43:00 AM GMT+8

    愈嚟愈有大師級風範.
    [版主回覆06/09/2008 14:33:00]大師? 喺邊道? 咦道只有老人J...

    ReplyDelete
  12. 阿蟲Monday, June 9, 2008 at 11:18:00 AM GMT+8

    大脾水貼係唔係原裝? 点整嫁? 好鬼正!
    [版主回覆06/09/2008 14:34:00]大脾水貼係用红彗星嗰set水貼...

    ReplyDelete
  13. BallMonday, June 9, 2008 at 5:54:00 PM GMT+8

    真係好detail, 正!! 膠條你有冇用evergreen這牌子? 佢比雙星多好多size. http://www.evergreenscalemodels.com/ 旺角如千里達, 英明等都有得賣.
    [版主回覆06/09/2008 14:41:00]唔該晒ball_kei兄啲tips! 我都有用evergreen, 但灣仔偉利無1.5mm, 而早幾日落大雨又唔想過海, 只好買双星2mm自己磨啦...

    ReplyDelete
  14. BillyMonday, June 9, 2008 at 6:24:00 PM GMT+8

    So..............good!! Looking forward on the finished day!! ^_^
    [版主回覆06/09/2008 14:41:00]Still a long way to go!

    ReplyDelete
  15. 喜樂的森Monday, June 9, 2008 at 6:51:00 PM GMT+8

    嘩! 真係一絲不苟! OT問題: 想請問為何我砌ZAKU VER2時想將喉管從框架中移去彈弓度, 但總是很硬做不到, 要逐粒辛苦地"轉"出來! 是否有聰明D既方法呢? 可能我唔知! THX!
    [版主回覆06/09/2008 14:43:00]我之前嗰隻红彗星都係要逐粒"超辛苦地推"出來... 仲攪到手指頭好痛添...

    ReplyDelete
  16. HathawayMonday, June 9, 2008 at 8:50:00 PM GMT+8

    用左噴槍?
    [版主回覆06/09/2008 14:44:00]無吖...

    ReplyDelete
  17. 一年戰爭高達迷Monday, June 9, 2008 at 10:16:00 PM GMT+8

    下半身骨架完成啦！o的噴罐金屬色噴得好靚，我幾時都係咁欣賞JKL兄既上色，好正 ！
    [版主回覆06/09/2008 14:45:00]多謝一年戰爭高達迷的讚賞...

    ReplyDelete
  18. tempoTuesday, June 10, 2008 at 1:28:00 AM GMT+8

    好仔細呀~ sexyhope san收到一定開心死..
    你諗住整高機動型比佢..?
    [版主回覆06/09/2008 17:56:00]係高機動型, 不過會係紅彗星版＋JKL custom的高機動型渣古! 階因佢話要JKL custom的Char'sザクII, 仲要黑色...(不過馬沙專用機都係红色喎)...

    ReplyDelete
  19. CUTuesday, June 10, 2008 at 1:47:00 AM GMT+8

    靚得你丫....非訂閱不可....
    請教下你先:補品 - 金屬噴射器 同 金屬動力管: 上色..要先噴金屬底油嗎?
    你砌得咁靚,忍唔住口問你...哈哈 !
    [版主回覆06/09/2008 18:00:00]多謝訂閱... 「有heart人」教落: 金屬補品上色前可先噴Mr Metal Primer - http://plajapan.com/467

    ReplyDelete
  20. TerenceTuesday, June 10, 2008 at 3:08:00 AM GMT+8

    早知你無糭我就post只上嚟啦```引誘下你都好呀嘛``
    原來都有用手油加~~~真係唔講都唔知添```好靚喔```一早以為係噴嘅添```
    真係用噴嘅得！用手嚟油都得！得咗！
    想請教下你手油嘅方法（我都試過，但油得好差``` ）同埋骨嘅颜色點溝嘅呢？
    補品係模型專用嘅補品嗎？（睇個包裝好似唔多似咁嘅``）
    [版主回覆06/10/2008 01:40:00]主色當然係噴油, 手油好難油到金屬feel... 只係D detail位係手油... 補品無錯係模型專用嘅, 可以入HKML找「 有heart模型改件精品店 」

    ReplyDelete
  21. DickyTuesday, June 10, 2008 at 4:49:00 AM GMT+8

    嘩!好精細的改做呀!!
    [版主回覆06/10/2008 01:42:00]下個blog講頭部的製作, 改得仲甘! 等多兩日再返來睇睇啦...

    ReplyDelete
  22. 搵老襯Tuesday, June 10, 2008 at 5:33:00 PM GMT+8

    真係好靚好details
    [版主回覆06/10/2008 09:42:00]唔敢當...

    ReplyDelete
  23. KakuTuesday, June 10, 2008 at 7:00:00 PM GMT+8

    死野真係好鬼正呀,尤其係個核水貼好有feel
    [版主回覆06/10/2008 11:03:00]個核水貼係用咗红彗星嗰set水貼...

    ReplyDelete
  24. 龍千影Wednesday, June 11, 2008 at 1:16:00 AM GMT+8

    渣古高雞動型＠ｏ＠"
    期待！
    [版主回覆06/10/2008 17:41:00]我都好期待你隻電擊古...

    ReplyDelete
  25. TerenceWednesday, June 11, 2008 at 3:29:00 AM GMT+8

    聽講星期三只渣古就出blog囉喔````好期待呀```
    但點解唔見你post其餘部分嘅進度嘅呢？
    P.S：你好似仲未講骨嘅颜色係點溝喔````
    [版主回覆06/10/2008 23:46:00]其餘部分仲未整吖嗎... 骨的颜色係双星TS-42罐噴...

    ReplyDelete

Subscribe to: Post Comments (Atom)